As with the cost, it is difficult to estimate the exact time that it will take for a bathroom renovations project since it depends on a variety of factors such as the size and requirements of the renovation. On average though, it takes anywhere between 2 – 4 weeks to complete a bathroom renovation with shorter projects that just need replacement/upgrade of appliances/fittings taking as little as 1 week. Our team here at Bathroom Renovations Sydney is highly efficient and ensures that minimum time is needed for your renovations project.
Splurge on the accessories. With so few accessories to consider, you can spend more on those you do need. “Invest in the faucet,” says Carolyn Cheetham, president of Design Works by Cheetham in Alberta, Canada. “It’s an opportunity to bring something fun and sculptural into the space.” Also, consider matching the faucet finish to other accessories in the space, such as the towel ring, mirror frame, and light fixture.
Be adventurous. Design treatments that would look over the top in other parts of the home are fine in the powder room. Deep dark hues, such as burgundy and eggplant, play well in these small spaces. Not that adventurous? Limit dark hues or unusual colors to wall paint. Pricey materials such as vessel sinks, custom floor patterns, and stone counters won’t be as hard on your budget because you won’t need as much as you would in a larger bath.
The wall-hung toilet’s supply line must have a male adapter with a temporary galvanized cap. Check the instructions on the toilet to get the proper location. Routing water supply lines is different in every bathroom, so you’ll have to adapt runs to your situation. But run the plastic drain lines and vents before starting any supply work. It’s much easier to route water supply lines around drain lines than to route drains and vents around supply lines. The same thinking applies to electrical work: Wait until the water supply work is finished before wiring.
Nail the bottom plate to the floor and the top plate to the ceiling. Then mark the positions of the shower base, toilet and sink. Lay out and toenail the wall studs into position (Fig. B) and the top plate for the low wall. On the opposite end of the shower, frame a matching 35-in. wide wall (see Photo 14) 60-1/4 in. (or the length of your shower base plus 1/4 in.) away from the first wall.
Here at Bathroom Renovations Sydney, we provide you with the complete range of bathroom renovations services for modern bathrooms, luxurious bathrooms, small bathrooms, and traditional bathrooms. Our complete renovations services include, but are not limited to, planning, designing, remodeling, construction, appliances removal/installation, fittings removal/installation, tiling, and paint. You can choose any one of these services, or our entire assortment of services to enjoy peace of mind with your renovation.
Yes, definitely. We recommend that you purchase appliances/tiles/fittings on your own so that you can choose products that perfectly suit your taste and needs. We will help you get in touch with trusted suppliers and will guide you through the correct size/type of products to buy but the ultimate choice will be yours. On the other hand, if you are looking for someone to take care of all the hassle of picking and choosing the best appliances and tiles, then we can do it all for you, too!
With just a few affordable changes, this powder room got an elegant new look. A slender pedestal sink adds a graceful shape to the room without taking up much space. The easy-to-clean wainscoting behind the sink adds a pretty architectural element in this small bath. Installing the painted beaded board just past the midpoint of the wall draws the eye up and lends a sense of height and a layer of charm.
Yes, all of our bathroom renovations projects are covered under a 7-year guarantee. We work with the best tradesmen and professionals in the industry to ensure that all work is done in compliance with the Australian building codes but at the same time, also provide guarantees for all work that we do. We are here to ensure the maximum satisfaction of our customers.
The key to a weatherproof, attractive glass block window both inside and out is to encase it in a custom-built wooden frame (Fig. A) with inside dimensions that are 1/2 in. taller and wider than the panel itself. That will give you room to adjust and shim the panel exactly and then inject expanding foam between the frame and the panel to lock it into the opening (Photos 3 and 4).