If your room is wider than the shower base, fur in the walls as needed to butt against the ends of the shower base (see Photo 14). Our bathroom is 6 ft. wide, so we added a floor-to-ceiling 2×6 wall at the showerhead end and a shorter 2×6 wall at the opposite end. We made that wall only 43 in. above the floor so we could use the top of the wall to hold shampoo and other shower supplies. The shower base usually comes with a special 2-in. drain fitting that you connect to the drain line (Fig. B).
For your remodeled bathroom to operate well, it’s critical to install vent and drain lines of the proper size and slope. Use a 2-in. line to drain the shower and 1-1/2-in. line to drain the sink. The vents for the sink and shower can be 1-1/2-in. pipes, but a toilet should be vented with at least 2-in. material. Make sure that the drain lines drop 1/4 in. for every foot of travel toward the main stack.

Bathroom Renovations Sydney did a superb job from start to finish when I wanted to get my bathroom redesigned and reconstructed. I opted for their traditional bathroom renovations service and the price they quoted was incredible. Despite initial speculations, the entire remodeling was done perfectly and my bathroom looks absolutely exquisite now! I would definitely recommend their home improvement and designing services.
Framing rough-in. This refers to any structural framing work that is required. Low-level remodels may require no rough-in framing at all, while others may involve work like framing in a new shower stall. While some skills are involved, DIYers can usually do this work if they have moderately good carpentry skills. The framing rough-in may require an inspection to make sure the work is done correctly. 
Toenail 2×6 blocks in the center of the shower 36 in. above the floor for the shower valve and 6 ft. 6 in. above the floor for the showerhead. Position the valve block so the plastic mud guard on the mixing valve will be flush with the finished wall surface. Attach the shower supply line and the hot and cold supply lines to the valve. Clamp the valve body and shower supply line to the blocks with copper pipe straps. Run copper water supplies to the new locations for the sink and toilet.
Interior bathroom demolition costs $1,000 to $2,300. Prices can go higher if you’re removing and moving walls to create a different footprint. For the experienced DIYer, this is a good place to save money by doing it yourself or assisting the contractor. However, demo can get expensive quickly if you take out a load bearing wall, cut electrical lines or break a water pipe. Avoid the risk by hiring a pro.
When vintage items filled the room, it’s neither modern nor traditional, but it called eclectic. An eclectic style does not quite fit some styles, such as modern, traditional, or retro. But it’s more like a combination of those styles with the addition of unique accessories. The eclectic designs in this bathroom are on the fixtures, vintage wallpaper, and a combination of white and black colors.

The tank is concealed within a 2×6 wall that’s built in front of the existing plumbing wall. It does require some plumbing rerouting because the waste line runs through the wall instead of the basic floor-mounted toilet flange (see Photos 8 – 12). The toilet can be ordered with a wall-mounted access panel/flush button like ours or with the panel mounted on top of a half wall. A ‘chair carrier’ (Photo 11) comes with the toilet. This steel framework contains the toilet and operating mechanisms and is designed to support the weight of the toilet.
The Save My Reno team definitely had a huge task on their hands. This dark and dingy bathroom was in desperate need of a little TLC.

Related: 20 Clever Ways to Save Money in Your Bathroom

Yes, with our affordable bathroom renovation packages, you can significantly reduce your costs by renovating more than one bathroom at a time. We have packages available for two bathroom renovations, three bathroom renovations, and above. If you choose to have two or more renovation projects completed by us, we will offer an exclusive discount that will help you get all bathrooms renovated at an affordable price.
The special-order fixtures, fittings, shower pan, tile and glass block panel can take weeks to get in hand, so do the necessary legwork and ordering well in advance. Before gutting the bathroom, check to make sure that there are shutoffs for all the fixtures or a master shutoff for the entire bathroom. If not, buy ball valve shutoffs sized to fit your pipes. Then turn off the main water supply line where it comes into the house from outside, cut the pipes feeding the bathroom and install the new shutoffs right away (see Photo 7).
If your would-be sanctuary is a major sore spot, you’re not alone. Bathrooms are second only to the kitchen on people’s wish lists of rooms to remodel, especially since the current economy-induced deferred maintenance has pushed so many past their 20-year lifespan. “At that age, bathrooms really start to get tired,” says Art Donnelly, president of Legacy Design Build in Mount Sinai, New York. “Leaky toilets, grimy grout, loose tiles—you name it, it’s probably an issue.”
This is really an incredible checklist and I am glad I came across this resourceful post. My family is planning to renovate our home before festivals. I think this post will definitely help us plan things in advance and ease our renovation process. I will definitely share this blog with my family and others. Thank you for sharing this blog with us and keep up the good work.
The Home Depot is a great place to buy your bathroom essentials and remodeling materials. We also provide top-rated design and installation services for homeowners across America. Besides undergoing full background checks, our hand-selected remodeling experts are local, licensed and insured. The Home Depot also offers a great selection of flexible finance options.
Framing rough-in. This refers to any structural framing work that is required. Low-level remodels may require no rough-in framing at all, while others may involve work like framing in a new shower stall. While some skills are involved, DIYers can usually do this work if they have moderately good carpentry skills. The framing rough-in may require an inspection to make sure the work is done correctly. 
Toenail 2×6 blocks in the center of the shower 36 in. above the floor for the shower valve and 6 ft. 6 in. above the floor for the showerhead. Position the valve block so the plastic mud guard on the mixing valve will be flush with the finished wall surface. Attach the shower supply line and the hot and cold supply lines to the valve. Clamp the valve body and shower supply line to the blocks with copper pipe straps. Run copper water supplies to the new locations for the sink and toilet.
Yes, all of our bathroom renovations projects are covered under a 7-year guarantee. We work with the best tradesmen and professionals in the industry to ensure that all work is done in compliance with the Australian building codes but at the same time, also provide guarantees for all work that we do. We are here to ensure the maximum satisfaction of our customers.
Turn off the main water supply to the house, and in a convenient location, cut the hot and cold water supply pipes for the bathroom. Also cut out and remove all the existing water lines and fittings in the bathroom. Finally, cut out and remove the vent section leading to the sink and the main stack 5 in. below the vent tee. Stuff rags into open drain lines to keep sewer gas out of the house.

Most people think "small bathroom," and they think cramped shower stalls, dim lighting, and vanities stuffed to the gills. And while a small bathroom may mean making a few sacrifices on space, it can also be welcoming and comfortable. Plus, consider the major pros of a small bathroom. With less square footage to deal with, it's cheaper to renovate, faster to clean, and easier to decorate.
Bathroom remodels provide 60 to 70 percent resale returns as a home improvement project. However, this project isn’t cheap. It is essential to plan your remodeling ideas ahead of time. Then, hire a remodeling contractor for the job. Ask questions, set realistic expectations, get accurate cost estimates and budgeting from the start. Also spend time learning how to work with a bathroom contractor.
×