Inexpensive shelves from a home center transform the wall above the toilet to provide a storage spot for bathroom essentials. Throughout the bathroom, a simple light-and-dark scheme helps the space appear larger, and the same scheme was applied to the vignette above the toilet. The dark tones on the shelves, picture frames, and art contrast with the white towels, photo mats, and bud vase.

Nail the bottom plate to the floor and the top plate to the ceiling. Then mark the positions of the shower base, toilet and sink. Lay out and toenail the wall studs into position (Fig. B) and the top plate for the low wall. On the opposite end of the shower, frame a matching 35-in. wide wall (see Photo 14) 60-1/4 in. (or the length of your shower base plus 1/4 in.) away from the first wall.
Drywall installation. Most remodeling jobs will involve opening up at least some of the walls and ceilings, and after the plumbing and wiring rough-ins have been inspected and passed, a drywall pro or DIYer can then install and finish the drywall. This is somewhat tedious work, but it is well within the skill level of most DIYers. The money-savings here are modest, though, because professional drywall installation is not pricey. 
Turn off the main water supply to the house, and in a convenient location, cut the hot and cold water supply pipes for the bathroom. Also cut out and remove all the existing water lines and fittings in the bathroom. Finally, cut out and remove the vent section leading to the sink and the main stack 5 in. below the vent tee. Stuff rags into open drain lines to keep sewer gas out of the house.
Preassemble the shower valve by soldering copper nipples and the shower supply pipe to male adapters and screwing them into the shower valve before fastening the valve to the blocking. That way you won’t damage the valve with heat from the soldering torch. Mount the valve 36 in. above the floor. You can mount the showerhead at any height, but plumbers typically mount them 6 ft. 6 in. above the floor.

Yes, all of our bathroom renovations projects are covered under a 7-year guarantee. We work with the best tradesmen and professionals in the industry to ensure that all work is done in compliance with the Australian building codes but at the same time, also provide guarantees for all work that we do. We are here to ensure the maximum satisfaction of our customers.


Industrial bathrooms design are trendy. It usually uses rouge materials, woods, and visible bricks. Some industrial furniture like lamps for lighting also gives a proper look for this design. Just like this mid-sized bathroom, it has a marble tile porcelain floor and gray walls. Therefore, the colors and accessories applied here make the industrial bathrooms design looks obvious.

Follow Fig. B, for the new drain/vent plan. The new shower drain is vented separately into the main stack (Photos 10, 12 and 13). Most bathrooms have the main stack positioned directly behind the toilet. The wall-mounted toilet shown here cannot be positioned directly behind the stack because there’s not room for the necessary elbows. If your stack is more than 12 in. to the side of the existing toilet, you can keep the same location for the wall-hung toilet. But if it’s directly behind it, you’ll need to swap the sink and toilet locations like we did.


On the other hand, if your home has one or more additional bathrooms that can fill in, and if you have moderate to advanced DIY skills, then there is no reason you can't take your time and do all or most of the work yourself. This route also has the advantage of giving you the time to find and buy all the materials for your bathroom, which can offer huge cost savings. 
The wall-hung toilet’s supply line must have a male adapter with a temporary galvanized cap. Check the instructions on the toilet to get the proper location. Routing water supply lines is different in every bathroom, so you’ll have to adapt runs to your situation. But run the plastic drain lines and vents before starting any supply work. It’s much easier to route water supply lines around drain lines than to route drains and vents around supply lines. The same thinking applies to electrical work: Wait until the water supply work is finished before wiring.
Turn off the main water supply to the house, and in a convenient location, cut the hot and cold water supply pipes for the bathroom. Also cut out and remove all the existing water lines and fittings in the bathroom. Finally, cut out and remove the vent section leading to the sink and the main stack 5 in. below the vent tee. Stuff rags into open drain lines to keep sewer gas out of the house.
Wall and Floor Tile: Ceramic, porcelain and natural stone are popular picks for floor tile in bathrooms. Materials will be the deciding factor here, but natural stone often costs more to install because it is difficult to cut and place. From natural stone and classic ceramic to glass and mosaic styles that mimic natural materials, wall tile options vary.

Glass block comes in 8-in. and 6-in. squares and 4 x 8-in. half-block rectangles. You’ll need to choose between real mortar grout joints and clear silicone–joined blocks. We chose the silicone system because we liked the clean, uninterrupted look. Whichever way you go, buy the panel preassembled and banded together as one unit, ready to set into the opening.
Bathroom Renovations Sydney did a superb job from start to finish when I wanted to get my bathroom redesigned and reconstructed. I opted for their traditional bathroom renovations service and the price they quoted was incredible. Despite initial speculations, the entire remodeling was done perfectly and my bathroom looks absolutely exquisite now! I would definitely recommend their home improvement and designing services.
×