The Home Depot is a great place to buy your bathroom essentials and remodeling materials. We also provide top-rated design and installation services for homeowners across America. Besides undergoing full background checks, our hand-selected remodeling experts are local, licensed and insured. The Home Depot also offers a great selection of flexible finance options.
The Save My Reno team definitely had a huge task on their hands. This dark and dingy bathroom was in desperate need of a little TLC.

Related: 20 Clever Ways to Save Money in Your Bathroom

Disconnect the trap from the tub, remove any clips, fasteners or screws that hold the tub to the wall, and demolish the old cast iron tub with a sledgehammer. Remove the sink and toilet. Turn off the electricity at the main panel and remove light fixtures. Cap the wires with wire connectors. Then rip out the wall finishes and surfaces clean down to the studs and pull out any insulation. If your ceiling is in good shape, use a utility knife to cut the drywall along the edges so the wall materials will separate cleanly from the ceiling.
With the rough plumbing complete and the toilet chair carrier in position, finish the electrical and add blocks as needed to support the sink (Photo 15), towel bars, grab bars, etc. Then close up the walls. We recommend cement board for durable tile walls and floors, but other tile backers are available at tile shops. Here are key installation tips:
Renovating the laundry room from time to time can be a refreshing experience and if you are looking to get your laundry renovated then this service is just for you. With our laundry renovations services, we help your laundry blend in perfectly with your home and design it so that you can wash, fold, iron, hang, or store laundry comfortable and with a peace of mind.
Homeowners often imagine that remodeling a small bathroom—one that is about 50 square feet or less—will be much quicker, much easier, and much less expensive than remodeling a large bathroom. And they are often surprised to find that it's only a little bit quicker, a little bit easier, and a little bit less expensive. The reason? A small bathroom has most of the same elements as a large bathroom and remodeling requires assistance from the same in-demand professionals as does a large bathroom. The reality is that a 50 square foot bathroom may be one-third the size of a large 150-square-foot bath, but it typically costs about 75 percent of a large bath in terms of time, money, and effort.
Before starting to renovate a bathroom, consider to determine your budget. The cost of remodeling a bathroom depends on the size, started from small to medium or master. Not only the bathroom, but the fixture price also depends on its size. Moreover, the fixture elements that you will probably need while remodeling a bathroom are new shower or bath, countertops, lighting, flooring, and cabinets.
Industrial bathrooms design are trendy. It usually uses rouge materials, woods, and visible bricks. Some industrial furniture like lamps for lighting also gives a proper look for this design. Just like this mid-sized bathroom, it has a marble tile porcelain floor and gray walls. Therefore, the colors and accessories applied here make the industrial bathrooms design looks obvious.
The Save My Reno team definitely had a huge task on their hands. This dark and dingy bathroom was in desperate need of a little TLC.

Related: 20 Clever Ways to Save Money in Your Bathroom

Yes, with our affordable bathroom renovation packages, you can significantly reduce your costs by renovating more than one bathroom at a time. We have packages available for two bathroom renovations, three bathroom renovations, and above. If you choose to have two or more renovation projects completed by us, we will offer an exclusive discount that will help you get all bathrooms renovated at an affordable price.
Toenail 2×6 blocks in the center of the shower 36 in. above the floor for the shower valve and 6 ft. 6 in. above the floor for the showerhead. Position the valve block so the plastic mud guard on the mixing valve will be flush with the finished wall surface. Attach the shower supply line and the hot and cold supply lines to the valve. Clamp the valve body and shower supply line to the blocks with copper pipe straps. Run copper water supplies to the new locations for the sink and toilet.

It's hard to believe this is the same bathroom! Light and airy with a pop of colour thanks to the wall art, this chic soaking tub leaves plenty of room for the standing shower and various knick knacks.

Related: 9 Major Mistakes to Avoid When Renovating Your Bathroom

With a DIY mind-set, the owners of this small master bathroom created a personal sanctuary on a budget. This Asian butcher table, found at an antiques shop, was repurposed for the vanity. The table maintains its authenticity with a simple above-counter sink. A new mirror adds a modern touch, while a pebble-tile "rug" on the floor adds texture and a spa-like accent.

There are also contractors who are perfectly willing to split the work with energetic and skilled homeowners. You can, for example, offer to do all the demolition and painting/finishing work yourself, in exchange for a discounted bid from a general contractor. And if there are other tasks you are able and willing to take on, discuss this with your contractor. But make sure to discuss it upfront. Time is money for a general contractor, and he will not want his progress delayed while a homeowner dawdles over installing the ceramic tile floor, for example.
Even the slightest of errors in bathroom renovations can be the cause of much misery and disappointment in the future. We understand this and therefore, allocate an expert team of renovators who are highly skilled at executing renovation jobs with utmost precision. We conduct a thorough planning and design phase before starting the renovation process so that everything is on point and perfect according to your specific requirements.

A DIY bathroom makeover is not complete without new floor tiles. But before you start grinding away with the grouting, use a mason’s chalk line to mark reference lines perpendicular (at a 90-degree angle) to the wall with the longest continuous line. This will allow you to keep your tiles in a straight line, avoiding the dreaded crooked tiling job.
Renovating the laundry room from time to time can be a refreshing experience and if you are looking to get your laundry renovated then this service is just for you. With our laundry renovations services, we help your laundry blend in perfectly with your home and design it so that you can wash, fold, iron, hang, or store laundry comfortable and with a peace of mind.
The wall behind the toilet can be almost any height. For a standard toilet height of 15 in., make the wall a minimum height of 43 in. If you’d like a higher toilet, make the wall that much higher. Or, make the wall go all the way to the ceiling. We built a short wall to conserve space and to create a shelf and a mirror alcove. The wall at the opposite end of the shower can be any height as well. We made it the same height as the toilet/sink wall so we could line up the accent tile and make a convenient shower shelf.
Preassemble the shower valve by soldering copper nipples and the shower supply pipe to male adapters and screwing them into the shower valve before fastening the valve to the blocking. That way you won’t damage the valve with heat from the soldering torch. Mount the valve 36 in. above the floor. You can mount the showerhead at any height, but plumbers typically mount them 6 ft. 6 in. above the floor.
Drywall installation. Most remodeling jobs will involve opening up at least some of the walls and ceilings, and after the plumbing and wiring rough-ins have been inspected and passed, a drywall pro or DIYer can then install and finish the drywall. This is somewhat tedious work, but it is well within the skill level of most DIYers. The money-savings here are modest, though, because professional drywall installation is not pricey. 
The Save My Reno team definitely had a huge task on their hands. This dark and dingy bathroom was in desperate need of a little TLC.

Related: 20 Clever Ways to Save Money in Your Bathroom

Mixing modern with antique is the secret to this bathroom's signature look. Both the vanity and sink/faucet combination are simplistic but foster vintage and contemporary aesthetics. This single-lever faucet is easy to use, and the tall spout is the perfect height to deliver water to the vessel sink. A nickel finish on all the fixtures creates a cohesive look in this master bath.
Nail the bottom plate to the floor and the top plate to the ceiling. Then mark the positions of the shower base, toilet and sink. Lay out and toenail the wall studs into position (Fig. B) and the top plate for the low wall. On the opposite end of the shower, frame a matching 35-in. wide wall (see Photo 14) 60-1/4 in. (or the length of your shower base plus 1/4 in.) away from the first wall.
The cheapest route of all also typically the one that takes the most time: doing all or most of the work yourself. A very (very) skilled DIYer with plenty of time and a group of willing friends and helpers may be able to finish a bathroom remodel nearly as fast as a general contractor, but very few homeowners fall into that category. And there is the issue of quality: good contractors will do the job professionally, while many DIY installations will be recognizable as the work of an amateur. 

A pedestal sink fits the home’s style but lacks storage, but a glass shelf and a new medicine cabinet stand in as handy storage. The homeowner suggests making sure the new cabinet will fit the existing hole before applying wallpaper in case the opening needs to be modified. Replacing the 1990s oak medicine cabinet with a white-framed version furthers the bathrooms lighter, bright aesthetic.
Focus on durability. The surfaces and fixtures will likely get lots of wear and tear, especially if children use the room. Plastic laminate flooring and countertops are durable and inexpensive, plus the kids likely don’t care if they have high-end materials. As for fixtures, you still want high-quality construction, including all-brass parts and a PVD (physical vapor deposition) finish that resists scratches, but go with basic chrome, rather than pricier nickel or bronze. On the walls, choose an interior paint that resists mildew.
Tile the walls first, then the floor. When tiling around the window, keep the tile about 1/8 in. away from the glass block. Tile the floor, starting by carefully snapping center lines to lay out border strips and field tile. Work from those lines to get evenly spaced tiles throughout the floor. Grout the walls and floors but caulk the inside corners between floors and walls and where walls meet.
Yes, we have a free quotation service that helps you better understand the cost structure of a renovations project. We believe in being transparent at all levels with our customers, and this is the reason we provide you with a comprehensive quotation with a breakdown of all costs (labor, resources, appliances, equipment, etc.). If you would like to get a customized quotation for your bathroom renovations project, please get in touch with our team and one of our representatives will visit you for understanding your exact requirements.
Industrial bathrooms design are trendy. It usually uses rouge materials, woods, and visible bricks. Some industrial furniture like lamps for lighting also gives a proper look for this design. Just like this mid-sized bathroom, it has a marble tile porcelain floor and gray walls. Therefore, the colors and accessories applied here make the industrial bathrooms design looks obvious.
×